Project Name: Ship Engine ME-LGIP Hills

End User: MAN Energy Solutions

사용장비:  PXI 2ea, MANMPC

내용: Simulate Dual Fuel ship engines to connect signals to engine ECU to enable fault diagnosis and engine simulation

Project Name: Inertial sensor - Racelogic

End User: Pusan National University

사용장비: LabVIEW

내용: Create CAN DB of CAN data from inertial sensors, save each separation display of X-axis_Acceleration, Y-axis_Acceleration, Z-axis, Pitch, Roll, Yaw, Temperature.

Project Name: Multi-channel Data Collector

End User: Busan National University

사용장비: LabVIEW, Scanivalve ZOC22B, SCXI AI, SCXI DO

내용: Scanvalve's ZOC22B multi-channel pressure sensor uses SCXI equipment to select channels and collect data. It is possible to select channels using 5bit DO, and to display and log representative values for one channel data logging, multi-channel slow switching logging, and multi-channel fast switching channels.

Project Name: DU LINE GATHERING

End User: SNT MOTIV

사용장비: LabVIEW, PLC, Vision, Servo Press, Tighten Bolting

내용: It improves the efficiency of the process and reliability of the product quality by registering the acceptance or failure with the MES server and determining the acceptance with the data registered at the start of each process.

Project Name: 2Stroke Engine Monitoring

End User: MAN EnergySolutions

사용장비: LabVIEW, Modbus, cDAQ9189, DIAdem, FlexLogger

내용: The pressure and temperature RPM generated when running the ship engine can be received by Kongsberg Mode Bus and NIDAQ, accumulated data, stored as a file, and graphed for each data with DIAdem to compare.

Project Name: 4Stroke Engine Monitoring

End User: MAN EnergySolutions

사용장비: LabVIEW, Modbus, Industrial PC, FlexLogger, DIAdem, cDAQ9189

내용:Pressure, temperature, RPM, P.COMP, and P.MAX can be checked by cylinder axis. In addition, users accumulate data measured over a desired period of time, store it as a file, and compare it as a graph for each data with DIAdem.

Project Name: OVERMOLD GEAR

End User: S&T MOTIV

사용장비: LabVIEW, PLC, Industrial PC

내용:If the torque value within the user's specified range is output to the graph by rotating the gear, the passed value is not detected if the torque value is defective or an alarm is output to the graph.

Project Name: GEN.6 LINE (Mixed Production)

End User: S&T MOTIV

사용장비: LabVIEW, PLC, Vision, Laser Marking, DB

내용: Even if a product's model changes, it automatically processes the product's model without the need for the user to specify the product's model.

Project Name: Pump Test

End User: Bosch Rexroth

사용장비: LabVIEW, PLC (Mitsubishi)

내용: Operate the pump to visually check various data such as pressure, RPM, temperature, etc. generated during operation, save data values by time zone, and determine whether the data can be verified by date and whether it is a normal product or a defective product.

Project Name: AE/DE HSG LINE

End User: S&T MOTIV

사용장비: LabVIEW, EXCEL, MES

내용: Collect data from the production process (pass, defect, torque, leakage, voltage, current, insulation, etc. and register it with the S&T server computer.

Project Name: Dynamo Motor Test

End User: Aerospace Research Institute

사용장비: LabVIEW, NI-9188

내용: Graph data generated during motor test (voltage, current, temperature, RPM, etc.) and data sent and received by RS485 communication

Project Name: Data Collection Program

End User: Institute of Production Technology.

사용장비: LabVIEW, cDAQ-9178, NI-9234,NI-9201, cRIO-9423

내용: Graph and store collected physical data and load as many stored data as desired to compare with previous data

Project Name: Hydrogen Charge Monitoring

End User: Donghee Industry

사용장비: LabVIEW, DAQ-9188

내용: Calculate the temperature and pressure when injecting hydrogen into the tank, and if the pressure and temperature are higher or lower than the user's set standard, the first warning is issued and shut down when it is outside the second set value.

Project Name: HTS_Sub TEST 

End User: S&T Motiv

사용장비: LabVIEW, Atraskopco PLC (LS Industry)

내용장비: Decompression test and bolt torque measurements are displayed in the UI to confirm with the operator.

Project Name: Torque Test

End User: Bosch Rexroth

사용장비: LabVIEW, PLC, OPC LabVIEW Inrtalogics, Bosch Intralogics

내용: It is a program that measures torque, stroke, and RPM of motors on the 1st, 2nd, and 3rd axes and prepares a report along with the corresponding graph.

Project Name: ERT Operator

End User: Jeju National University

사용장비: LabVIEW, PXI-2536 SWITCH

내용: It is an improvement project that controls the PXI-2536 SWITCH module and automatically changes the contact point in the experimental environment where data were collected by manually moving the contact point directly. It programatically changes the interface so that various experimental conditions can be met immediately.

Project Name: Simulator

End User: Nuclear Research Institute.(DAEKYEONG Engineering) 

Equipment used: LabVIEW, PXIE-1209 Pulse, PXIE-6739 AO, PXI-6511 DI, PXI-6512 DO

Content: It is a device that simulates and monitors multi-channel AO, DO, DI, and pulse output. The desired channels can be grouped and used, signals can be manipulated and monitored in various ways by automatic/manual/programming, and signal response time can be measured

Project Name: Relay Test Equipment

End User: Hanul Nuclear Headquarters (WOO RI Technology)

사용장비: LabVIEW PCIe-6351 DAQ, PCI-6509 DIO

내용: It is a device that tests relays used by nuclear headquarters before input. Users can specify specifications so that they can test various relays, and also specify the type of test and the number of tests.

Project Name: ESM Line

End User: S&T Motiv

사용장비: LS XGT PLC, Lenze Servo, F620 Leak Tester, OMRON Vision, TOS5200 HiPOT, ST5520 Insulation

내용: S&T Motiv's ESM production line stores equipment manual/automatic manipulation, production count, MES, product quantity/disjudgment and results.